Owen369

Also very hesitant an a little jerky is it just my driving being use to dirty dieselsss [emoji85] Sent from my iPhone using Tapatalk

Ended up with new oem one fitted it tested oil pressure cold start up is 80psi Warm idle is 30psi And as soon as you rev goes to 90psi Pressures sound all good? Going to order some gauges today and a pod still dont trust the car [emoji85] Sent from my iPhone using Tapatalk

Anyone know were to get a killer b one from next day delivery uk stock like? Going to order a new oem tomorrow morning otherwise family member can weld braze ally weld ect anyone modded one? The pipe was sweet when fitted sure of it i cleaned it fitted new oring ect sure i would of spotted it [emoji25] oil pressure was showing 80psi at 5000rpm rev so hopefully no damage Sent from my iPhone using Tapatalk

Changed sensor and light seems all good but i was not satisfied as only goes off at 2.5psi so got a pressure gauge and Done the checks thats at idle just after starting so i dropped the sump and pick up pipe and found can not get one today being sunday need one asap going to ring advanced automotive or roger clark and next day it unless someone knows anywere to get one from in the West Midlands area Sent from my iPhone using Tapatalk

Change sensor * Sent from my iPhone using Tapatalk

Drove it most of the day cleaned it ect. Oil light came on when i parked on a hill. When started back up took around 10-20seconds to go off And since has flashed on and off after i started it for about a second on flat ground. Going to have a look tomorrow chance sensor at front of block and get a pressure gauge on it but runs fine and dont like to say it but no engine light on dash yet Sent from my iPhone using Tapatalk

Yes relief just read codes and got this [emoji85] car runs sweet cleared codes going to have spin round the block now see if shows back up. was going so well [emoji85] many thanks for support guys been alot of help [emoji108][emoji106] Sent from my iPhone using Tapatalk

Oil changed to the expense stuff and oil light now goes off as soon as its started [emoji106] also hks oil filter now on [emoji106] jacked her up at the front and burped it ect got all bleed up heater now red hot [emoji108] been out few times running it up and just been for a 40 mile trip on b roads. Toward end of the trip the engine light came on pulled over no leaks temp fine running fine so will plug in tomorrow. Only thing i can say is its a little hesitant as comes on the boost but only slightly apart from that spot on. Impressed by performance to be fair [emoji106] Sent from my iPhone using Tapatalk

Got it in and run it up for a while oil light took a bit to get on turned over without starting for a while oil light stayed on. Started Engine and took around 1 min for oil light to go out this normal? And hope the pump is ok piggysniffer had enough of buyin bits now [emoji25]. Also heaters are blowing cold. Going to blow heater matrix out tomorrow see if it blocked Sent from my iPhone using Tapatalk

Have heat wrapped all the bits i can see got all the bottom heat shields off an wrapped them as sheilds were scrap. Will check the up pipe after work and wrap that also [emoji106] may be coming off for decat in future. timing all done covers on the ect. May be dropping it back in tonight. Just had a read up on secondary air system. Think i will leave it want the car pritty much standard, for now anyway Many thanks guys [emoji106] Sent from my iPhone using Tapatalk

Getting somewhere again [emoji106] Sent from my iPhone using Tapatalk

Yerrr was advised to pay that way as only got email and phone number for the guy so hopefully all covered nightmaree don't cover it hope get to building tomorrow Sent from my iPhone using Tapatalk

Sent from my iPhone using Tapatalk

£500 heads cam lobe. snapped aswell on cam cover bit Sent from my iPhone using Tapatalk

Heads come and are scrappp no gd all picked up same as mine not as bad but not good enough for me to use. After big argument with the chap i now have a paypal depute on the go for my £500 back for heads. He says send them back want my money back first. On the plus found a set off a engine where chap is putting ej20 heads on ej25 bottom end. Local been got them very little wear on cams and lobes alot better than £500 ones got them for £300. So longgg day Sent from my iPhone using Tapatalk

Cleaned everything with a fine brush and petrol ect. Didn't see any cracks or anything in pick up how much you order one for? Oem one? Or upgradeed killer b thing Sent from my iPhone using Tapatalk

Piggysniffer yes sump on all built up to point of fitting heads. Waiting on them have tracking saying will get them tomorrow so be back to building then. Nightmaree Sent from my iPhone using Tapatalk

Many thanks mr b as always a university professor grade A answer [emoji108] I have a picture of a very clean workshop in my head. [emoji106] still waiting on heads 3 weeks now. Chap assures me they have been sent tracking says still at access point, just want to drive the thing now [emoji22] Sent from my iPhone using Tapatalk

Got there in the end nightmaree to find that oil is. How long shall i run the mineral oil? And it wont harm any of other internals will it just bed the rings in? As never done that before. Still waiting on heads so heat wrapping tonight Sent from my iPhone using Tapatalk

Got some gulf 10w/40 ester synthetic Many thanks guys subarus are hard work [emoji85][emoji120] Sent from my iPhone using Tapatalk

Mr b were do i get this 10w/40 fully synthetic easter based oil from? [emoji120] Gsf. Euro. Halfords. Local parts shop. Engine place tried them all havent got a clue what im talking about they havent [emoji85] Sent from my iPhone using Tapatalk

O no mr b[emoji85] i hope its bomb proof after all this. Yes luckly we have spanner skills otherwise would have been a fortune of a job. Will do a run up ect thanks for info [emoji108]once againnn. Jay762 waterpump going on tonight ( many thanks for that) and heads if they turn up today[emoji106][emoji100] Sent from my iPhone using Tapatalk

Got magnetic sump plug to [emoji106] Sent from my iPhone using Tapatalk

Honed bores yes. Was going to get a cheap oil to wash though first [emoji106] then a good fully synthetic oil and filter change like you say. What oil you run fully synthetic? As in 5w40? Ect Sent from my iPhone using Tapatalk

Getting somewere [emoji106]what oil do you all recommend? Got to get some good stuff tomorrow Sent from my iPhone using Tapatalk