Brucey 95wrx
-
Posts
31 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Premium Membership Discounts
Subaru Videos
Subaru News
Everything posted by Brucey 95wrx
-
Compression test is complete same reading on all cylinders
-
All readings are exactly the same 160 psi ignore the first photo
-
-
This can’t be good surely all plugs are the same as this
-
I was told the darker plugs are towards the gear box (coil packs and injectors)
-
Is there anyway I can send you a video of what it is doing
-
No it still stutters and pops in neutral and stand still but it will rev past it if you really push it but it sounds awful
-
It does throw an engine light like if you unplug the maf or the map so I know it stores codes because I used to get code 33 a lot
-
Just to add the Rev counter when it reaches 4000 begins to bounce back and fourth between 3500 and 4500 rpm
-
Yeah I was rotating cam so lobe was facing away from the lifter do I compression test with a warm engine or cold I’m assuming warm as all materials would have expanded and give me a true reading?
-
What are lash caps sorry complete novice
-
I did have valves reseated while heads were off
-
Only 2 of the 8 on passenger head would twist but how do you adjust these?
-
I have iridium heat 7 as running around 330 bhp on a chipped z4 ecu they are gapped at 0.6 i have plugged the black connectors in and the engine light just stays on no flashes I have disconnected the battery and left over night to reset ecu but still it persists is there anyway I can upload a video?
-
The gasket put on was a 1.4mm mls I need to re check the compression but I have no valve tolerance at all is this right with the hydraulic cups?
-
Deffo firing on all 4 driving it around town up to 4000 rpm you would not suspect a fault at all sounds good ticks over ok plugs are all a great colour it’s almost as if it is hitting a limiter at 4000 and shutting down the ignition timing which is causing backfire compression was at 169 psi on all cylinders before the head gasket was replaced with the throttle closed
-
My car is juddering and back firing at 4000 rpm just before the turbo kicks in after having head gaskets replaces so far I have changed fuel filter new plugs new coil packs green label maf turbo is brand new swapped injectors with spares still the fault persists but no check engine light It even stops at 4000 stationary and starts popping and banging
-
I have a 95wrx import and keep getting code 33 vehicle is in limp mode seems to be retarding the ignition at 4000 rpm my speedo clocks are mechanical so cable driven and the speedo works fine as far as I’m aware and reads in mph any ideas?
-
Thankyou very much for your help I shall try this over the weekend
-
Yeah it was new and genuine I even retested it with the old one still does the same I am baffled 😯
-
Hi buddy thank you for the reply I have done this this morning and the gauge reads nothing when that wire is removed?? Thanks 🙏
-
Having issues with my temperature gauge it is reading red before I even start the car it has had new water pump and genuine thermostat everything was fine for a couple of months after this I then parked the car up for 3 weeks got in it and started it and the gauge went straight to red I have now changed both coolant sensors on the crossover pipe any help would be really appreciated thank you
-
Yeah that would be great if you could buddy thank you very much 👍🏽
-
Yeah the speedo works fine nice smooth motion I’ve only just got it back on the road after my cam belt slipped 2 teeth and now yet another problem after 10 mins of driving 😂
-
Yeah mine is mechanical I have taken all of that apart cleaned with electrical contact cleaner hopefully it will work being mechanical will I have a sensor on the gearbox or is just the cable that spins?
