Jump to content

What turbo +won't boost


Calq98
 Share

Recommended Posts

It has a alcatek ecu.. And from what I have read they can delete the maf with This map setup. I know this probably wouldn't cause lumpy idle but what about the actuator? Am I supposed to be able to

Move the arm fairly easy? I guess It would be an idea to try another solenoid first

Link to comment
Share on other sites

I've found out why the car was idling crap.. Fluctuating up and down. I cleaned the idle control

Valve and seems to idle fine now..however I've tried another boost solenoid which works.. And that clicks twice when turning ignition on and green plugs connected.. But does not continue clicking. The restrictor pill is in the correct place. I've ran new vac hoses standard setup,bypassed the solenoid.. And still no boost. Actuator is goosed ?

Link to comment
Share on other sites

no idea.. I'm still not 100 percent those boost solenoids are working correctly.. Why does one click once and the other clicks twice. The amount of Subaru sites I've read and they say the solenoid should continue clicking on diagnostic mode..is there anything else that should work when green plugs connected and turn ignition on? So I can rule out whether the map supports the test mode?

Link to comment
Share on other sites

Yeah non of that happens. Just hear the solenoid click twice and that's about it.. So I'm guessing the green plug self check doesn't work with this ecu.. These cars are more complicated than I thought. Also trying to find a standard actuator is a problem as I can't find one

Link to comment
Share on other sites

The pic is info on that ecu from their site. Think I'm going to phone them

With the ecu number and ask about it so I'm aware about it. I'm guessing it's a vf23 as it ihi written on it. And from what I've read the v3 runs the vf23? Or am I wrong ?

post-4666-0-73199000-1436732530_thumb.jp

Link to comment
Share on other sites

I think your right on the turbo,

silly thought do you know if it has more than one map ?

Could be that there's two, a full boost set up and maybe a fuel saving, low/no boost map as well and it's just on the low map ?

Sent from my SM-G850F using Tapatalk

Link to comment
Share on other sites

No idea mate. This is why I need to phone alcatek if I can find out All the details. This Bladdy car is driving me insane. Just aswell I bought this as a project track car.. and for peanuts.

Link to comment
Share on other sites

Try dropping a mapper a email to see if the factory self code check works with a alcertek ecu, as I said before the oe ecu code check might not work with your aftermarket ecu and that might be why it's not running a full diagnostic check (only clicking a few times)

although a faulty actuator does seem to cover your symptoms, returning the boost vacuum system or anything else back to standard might not work if the current aftermarket ecus map has been set up with the "as you bought it " pipework . If you do want to try to get it back to standard you might want to fit a standard ecu , if the car hasn't got many mods as this will have a standard map too .

As stants said it could possibly even be something as simple as a low boost setting cos you can have loads of added features. .... twin mafles maps ,anti lag, launch control or even maps for different grades of fuel (95 Ron or meth mix) .

So I'd suggest to preferably get a mapper to check the codes on the ecu if not fit a standard ecu (if the cars not heavily modded) and second hand actuator with the v3 sti oe vacuum line set up .

Link to comment
Share on other sites

Yeah I'm going to get ecu codes tonight and contact alcatek.. I'm 100% sure the car doesn't have different maps,a map with low boost because the guy who built the engine 2 years back, I've spoken to him he never mentioned it had something like that and when my mate who I bought it off picked it up the guy who built in( a friend of ours) went with him and then it had no boost.. So basically my mate bought it very cheap and never did anything with it.. Sat in his garage for a year or so and now I've bought it for project..and for the vac lines, the guy who bought it said he put the boost controller In with the vac lines how they are. And it used to be fine, boosted how it should.. I've found a site that does stock actuators so

I'm going to order one of those.. And just check about the ecu and see if the self check does work with that ecu. I've had someone mention that they think the wastegate could be stuck open?

Link to comment
Share on other sites

Could be the same issue, if actuator dead or springs gone then the w/g could be open worst, case somethings broken off and has lodged the w/g open,

I'd pull the turbo and see

Sent from my SM-G850F using Tapatalk

Link to comment
Share on other sites

The actuator controls the wast gate which controls the amount of exhaust gasses allowed to pass through the turbo . Otherwise the turbo would keep spinning and creating boost until it went bang .

You could try disconnecting the actuator arm from the waste gate lever ,check it's moving freely and cable tie the waste gate shut.

It's just to see if it creates any boost at all ,don't drive it to far or run it too long as it's only a crude way of seeing if the actuators fubar before you buy one [emoji6]

Link to comment
Share on other sites

I know this sounds silly. But should the rod from the actuator to

Wastegate arm push outwards ? Because I can push the rod away from actuator. If I disconnect the rod and tie the wastegate like u said. Which way would be closed.. ? I've put the pic so it makes sense. Thanks for ur help again guys.

post-4666-0-46691100-1436790538_thumb.jp

Link to comment
Share on other sites

Towards the actuator would be closed (actuator arm pushes to open the waste gate )

Someone's selling a tdo4 on here in the for sale section with pics of the hot side which shows the waste gate from inside so you can see the "flap" and arm

Just don't rev it to much or drive it as I wouldn't want you to damage anything by having the waste gate shut without any control over how much boost the turbo's producing [emoji6]

Link to comment
Share on other sites

Gonna sound thick here. Surely if the actuator is buggered

the wastegate would stay shut and it should build boost? The pic does make sense tho.. Or would a buggered actuator do something else ?

Link to comment
Share on other sites

pretty sure the actuator arm is in as far as possible. I temporarily tied it with cable ties to try keep the flap shut. And still no boost. I have a stock brand new actuator coming but think it's even that now. Unless like u say the flap isn't shutting completely but certain it is..what next ? Wishful thinking but if both solenoids are buggered or not working on the car.. With the flap tied shut should it still create boost?

Link to comment
Share on other sites

Tbh I've never tried to manually hold the waste gate shut but logic tells me that if it won't make boost with it shut and there's nothing connected to tell the turbo to do anything but flow air the fault should be after the turbo

The vacuum system to and from the boost solinoid are not in use when you ran a straight vac line from actuator to turbo and the fault was still there .so I don't think it's those .

Now you've held the waste gate shut without using the actuator it doesn't sound like the actuator either.

I'm sort of running out of ideas to try and without physically seeing it's never easy .

My last few straws would be

Faulty turbo not making boost cos it's fubar

Air leak after the turbo letting the boosted air escape before it enters the engine This could caused by....

a vac line missing /split that's runs from the inlet manifold venting air

Y pipe under the tmic split /leaking

Inlet manifold gaskets leaking under pressure.

Any luck with the ecu codes ?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share







×
×
  • Create New...




Forums


News


Membership


  • Insurance
  • Unread Content
  • Support