Scubzjames Posted May 1, 2017 Share Posted May 1, 2017 Just wondering what people thought was the best stuff to protect the underside of your motor with? what about wax oil? Or thay bitchumen stuff? Any ideas? Quote Link to comment Share on other sites More sharing options...
David Wilkinson Posted May 1, 2017 Share Posted May 1, 2017 I'll be using waxoyl on mine. It seems to be good stuff. Just make sure you use a power washer to clean off your area first. If you wanted to go all out you could use dinitrol. Quote Link to comment Share on other sites More sharing options...
stants Posted May 2, 2017 Share Posted May 2, 2017 Waxoil does tend to go everywhere, I've had bad experiences in the past I now usually use the hammerite under body seal to do the floorpan and rear arches, then get some rattle cans for inside the box sections and a few places you can't reach Then get a couple of the Sent from my SM-G930F using Tapatalk Quote Link to comment Share on other sites More sharing options...
Fastboy67 Posted May 16, 2017 Share Posted May 16, 2017 Just been reading in jap performance mag about a company called krown that use some kind of mist spray that attacks the likes of surface rust and basically gets underneath it to protect the metal. It eventually turns into a gel so never sets and doesn't fall off or get chipped so protects for longer. Takes about 4 hours to do a car. Not sure on cost though. Quote Link to comment Share on other sites More sharing options...
Tidgy Posted May 16, 2017 Share Posted May 16, 2017 2 minutes ago, Fastboy67 said: Just been reading in jap performance mag about a company called krown that use some kind of mist spray that attacks the likes of surface rust and basically gets underneath it to protect the metal. It eventually turns into a gel so never sets and doesn't fall off or get chipped so protects for longer. Takes about 4 hours to do a car. Not sure on cost though. Sounds expensive tbh Quote Link to comment Share on other sites More sharing options...
Fastboy67 Posted May 16, 2017 Share Posted May 16, 2017 Iv left the mag at work so I'll check the morra and see if there's any mention of costs. Apparently the Canadian army use it on there vehicles. Quote Link to comment Share on other sites More sharing options...
Tidgy Posted May 16, 2017 Share Posted May 16, 2017 $119 dollars in the US, so i expect we'll be gang raped and it will be £500 2 Quote Link to comment Share on other sites More sharing options...
Piggysniffer Posted May 17, 2017 Share Posted May 17, 2017 Gonna have my car done at some point, so interested in this Quote Link to comment Share on other sites More sharing options...
stants Posted May 17, 2017 Share Posted May 17, 2017 13quod for a tin of underbody seal and a brush, save your money by not seeing a specialist, Wirebursh all loose crud, then prep the rusty bits then apply coat Sent from my SM-G930F using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
Fastboy67 Posted May 17, 2017 Share Posted May 17, 2017 Small cars start at £190 rising to £320 for larger more complex cars Quote Link to comment Share on other sites More sharing options...
stants Posted May 17, 2017 Share Posted May 17, 2017 Before Sent from my SM-G930F using Tapatalk Quote Link to comment Share on other sites More sharing options...
stants Posted May 17, 2017 Share Posted May 17, 2017 After Lasts for about 3 years before needs doing again but much cheaper than paying someone to do much the same job Sent from my SM-G930F using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.