Jump to content

New Owner..


UK2T
 Share

Recommended Posts


3 hours ago, Jay762 said:

Wotcha and welcome - clean motor you have there - very nice, has it had any work done?

Thanks.. Yeah few little bits

STI intercooler, strut brace

TD05 turbo new 😆 

OMP subframe brace

Whiteline anti roll bar 

Adjustable shocks eibach springs

Anti lift kit 

Straight through system.. Made 277bhp/280lbs  a few years back 

Do have a little issue with it but probably can't say in this thread.. 

Cheers.. 

  • Like 2
Link to comment
Share on other sites

15 hours ago, UK2T said:

Thanks.. Yeah few little bits

STI intercooler, strut brace

TD05 turbo new 😆 

OMP subframe brace

Whiteline anti roll bar 

Adjustable shocks eibach springs

Anti lift kit 

Straight through system.. Made 277bhp/280lbs  a few years back 

Do have a little issue with it but probably can't say in this thread.. 

Cheers.. 

nice mods - sorted the handling as well as a little power :biggrin:

 

dependant on what the issues are (as Ghost said) either post here or create a thread in the closest match section - The reason for the separate thread is two fold

1) it gets specific answers to questions and initially it will focus attention / increase visibility etc - it then may take on a life of its own and go off on a complete tangent there is absolutely no guarantee of staying on topic with this forum :tongue:

2) This is the main one - it may help others who are suffering the same issues being easier to find not being potentially buried in an unrelated thread

but the choice is yours :wink:

  • Like 1
Link to comment
Share on other sites

Thanks.. yeah she needs a bit of tlc mainly rear arches.. couple of dings here and there.. aiming to get all bodywork sorted and break the 300bhp barrier by summer :biggrin:fingers crossed.. 

  • Like 1
Link to comment
Share on other sites

I'm hoping mine will be as dam close to the 300BHP, 

got a full decat straight through system,

upgraded fuel pump

upgraded air filter

plus being an import STI, which is around the 275BHP as standard so I need to remap mine soon to get the fuel gauge under control :biggrin: plus installing the above too!!!!

 

  • Like 1
Link to comment
Share on other sites

Yeah must be standard :angry:.. Yeah I have them I'll get better pics tomorrow.. Will get it re-mapped when ecu finally calms down.. 

Scooby clinic.. Are you wheels ok?! :biggrin:

Will check import car parts for the gaskets as well.. 

Link to comment
Share on other sites

1 minute ago, UK2T said:

Yeah must be standard :angry:.. Yeah I have them I'll get better pics tomorrow.. Will get it re-mapped when ecu finally calms down.. 

Scooby clinic.. Are you wheels ok?! :biggrin:

Will check import car parts for the gaskets as well.. 

Lol :happy:

Do you have a good tuner near you?

Link to comment
Share on other sites

Sorry couldn't help it.. :angel_not: know a few around Northampton not scooby specialists though will have a look.. 

Would a remap sort the idle/rough running issue any quicker lol.. 

Link to comment
Share on other sites

Its hard to say really, the rough idle could be all sorts.  Have a search on here first for similar issues/solutions, maf, vac hoses etc.

If your down Aylesbury way, Ive used DSA for over 10 years who are a Jap tuning specialist with dyno.

Link to comment
Share on other sites

Yeah had a read of the others plug gaps etc.. Thing is it was sudden which made me think sensor was running perfect before that maybe the rough roads around me contributed to it.. 

I'll have a look now.. Maybe worth ringing them see if they have dealt with similar situation.. 100 key turns to sort out jeez..

 

Link to comment
Share on other sites

What supporting mods do you have making that power?

Ideally to get your 320 you need: Decat turbo back exhaust, free flow panel filter(or induction kit depends personal taste) 3 port boost solenoid(UK cars only have 2 ports) upgraded fuel pump(avoid the risk of running lean) PFR7B spark plugs came heavily recommended for me. It seemed to be one of the main criteria when I was being mapped as the first questions he asked were "which plugs and how old are they?".

I have 3" turbo back decat zorst, cosworth panel filter, rcm fuel pump, 3 port solenoid(2ND hand from an import) pfr7b plugs. Here's my map.

705dedb7f2a1512cc5125564f49f7079.jpg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share






×
×
  • Create New...




Forums


News


Membership


  • Insurance
  • Unread Content
  • Support